PCMCIA FAX/Modem Installation Diskette Ver. 1.4

1. This diskette contains :

*       README.TXT  : This README file
*       PC_CARD.INF : .INF file for both Windows 95 and NT 4.0
*       MDMEN.EXE   : Fax/Modem Enabler
*       MODEM.INF   : .INF file for Remote Access Service (RAS) of NT 3.51



2. How to install the modem for Windows 95

       (1) Select "Driver from disk provided by hardware manufacturer" item
           at the "New Hardware Found" window, when you plug the PCMCIA
           Fax/Modem card into the PCMCIA slot of your Windows 95 system
           at the first time.
       (2) Input the path "A:\" to load the INF file.
       (3) Press "OK" button.



3. How to install the modem for Windows NT 4.0

       (1) Make sure the PCMCIA card is plugged into the PCMCIA slot.
       (2) Start up the Windows NT 4.0.
       (3) Double click the Modem Icon in "Control Panel" window.
       (4) In "Install New Modem" window, press "Next" button to auto-detect
           the modems in the system.
       (5) Press "Change" button to change the modem type.
       (6) Press "Have Disk..." button.
       (7) Input path "A:\" and press "OK" button.
       (8) Select a correct modem type e.g.,"PCMCIA 56Kbps FAX+Modem"
           and then press "OK" to accept the modem type.
       (9) Press "Finish" button.


4. FAX MODEM ENABLER

The enabler, MDMEN.EXE is used to initialize the modem when you are not
using Card Services.  You can use the Enabler as DOS command or DOS driver.
It means that you can load the enabler from the DOS prompt or put it into the
AUTOEXEC.BAT or put it into the CONFIG.SYS to load it everytime you start your
computer.

        MDMEN [/COM=m] [/IRQ=nn] [/SLT=n]

        where
            COM=m  Specify the COM port number (m=1 -- 3). Default is 2.
            IRQ=nn Specify the interrupt request number in decimal. Default is
                       4 for COM1, 3 for COM2, 4 for COM3, 3 for COM4.
            SLT=n  Specify the slot number the Fax/Modem card plugged.
                       Default is auto-detection.


5. TECHNICAL NOTES FOR ENABLER

   (1)  Most communication software follows the Interrupt settings and
        I/O address settings as shown below:

                        IRQ Number        I/O Address

               COM1:        4                 3F8
               COM2:        3                 2F8
               COM3:        4                 3E8
               COM4:        3                 2E8

   (2)  If you are using Windows 3.1X, you can change the IRQ under the
        CONTROL PANEL - PORTS - ADVANCED dialog box. If you change the
        COMPORT and IRQ under Windows, be sure that it matches the parameter
        in the MDMEN.EXE.


   (3)  Two COM ports cannot share an interrupt even the default value is
        the same for example COM1 and COM3 or COM2 and COM4. If your system has
        COM1 and COM2 already, you may run MDMEN with /COM=3 and /IRQ=n where
        n is an available interrupt number other than 3 or 4. When you run a
        modem application program, the COM prot number and interrupt number
        specified at application should be to same with the parameter specified
        at MDMEN.EXE.


6. How to use the modem in Remote Access Service (RAS) of Windows NT 3.51

   (1) Install the Remote Access Service in your NT3.51 system

       1) Double click the "Network" Icon in "Control Panel" window.
       2) Make sure that a LAN driver has been installed in the system.
          Otherwise, the installation of Remote Access Service will fail.
       3) Press "Add Software..." button.
       4) Select "Remote Access Service" item and press "Continue" button.
       5) Input the path of NT3.51 source and press "Continue" button.
       6) Select the COM port number associated to the PCMCIA FAX/Modem card
          then press "OK".
       6) Press "OK" to detect modem type.
       7) If no corresponded modem type has been detected, select any modem on
          the list e.g., "Generic 144 PCMCIA modem" just for RAS installation.
          Press "OK" to accept the selection.
       8) Press "Continue" button to start the RAS installation.
       9) Press "OK" to complete the Network Setting.
      10) Select "Don't Restart Now" to continue the further installation.

   (2) Copy "A:\MODEM.INF" file to Windows NT 3.51

       1) Double click the "File Manager" Icon in "Main" window.
       2) Copy "A:\MODEM.INF" file to the "system32\ras" sub-directory of
          Windows NT 3.51.
       Example: The directory of NT3.51 is "C:\WINNT351".
                COPY A:\MODEM.INF to C:\WINNT351\SYSTEM32\RAS
                to replace the original MODEM.INF file in RAS directory.

   (3) Install the correct modem type

       1) Double click the "Network" Icon in "Control Panel" window.
       2) Select "Remote Access Service" item in "Installed Network Software"
          list box.
       3) Press "Configure" button to enter Remote Access Setup menu.
       4) Press "Remove" button and press "Yes" button to remove the "Generic
          144 PCMCIA modem" installed before.
       5) Press "Add" button to add modem.
       6) Select the COM port number associated to the PCMCIA FAX/Modem card
          press "OK"
       6) Press "OK" to detect modem type.
       7) Press "OK" to accept the modem detection.
       8) Press "Continue" button to start the RAS installation.
       9) Press "OK" to complete the Network Setting.
      10) Select "Restart Now" to restart the NT system. Now the Remote Access
          Service has been installed completely.