D-Link DFE-550TX FAST Ethernet 10/100 Adapter Installation
                            for Windows 2000

 Getting Started
 ---------------

    The Windows 2000 installation CD is needed to complete this
    installation.

    Windows 2000 Installation Procedure
    -----------------------------------

    Windows 2000 had supported this adapter, and the driver version is
    v1.0.5. To use the bundled driver ...

    1. Make sure your computer is power-off.

    2. Plug the adapter into one PCI slot of your computer.

    3. Turn on the power. Windows 2000 will find and install
       the driver automatically.

    Update driver from diskette
    ---------------------------
    The following steps can help you update the bundled driver to
    the one in the Adapter Drivers Diskette/CD-ROM.

     1. Open Control Panel, double click "System" icon to open System
        Properties.

     2. In the "Hardware" sheet, you can see the "Device Manager" bottum.
        Click to open Device Manager.

     3. Use the tool bar to make sure you "View" "Devices by type".
        Than you will able to find

        D-Link DFE-550TX 10/100 Adapter

        in "Network Adapters" group. Double click it to open its property.

     4. In the "Driver" sheet of the adapter's properties, there is a button
        named "Update Driver". Click it, the Upgrade Device Driver Wizard
        will show up to help updating the driver.

     The following steps will lead you through the wizard ...

     1. The first page is the welcome messages, click "Next" to continue.

     2. Select "Search for a suitable driver for my device (recommanded)",
        and click "Next".

     3. Check "Floppy disk drivers" and/or "CD-ROM drivers". It depends on
        where you driver files are. Click "Next" to continue.

     4. The wizard will still found the bundled driver now, check "Install
        one of the other drivers"

     5. The wizard will list all the driver it found, and there should be a

        D-Link DFE-550TX FAST Ethernet 10/100 Adapter

        located in you diskette or CD-ROM drive. Highlight it and click
        "Next" to continue.

     6. The wizard will copy and load the driver, than you will see "Finish"
        bottum. Click it and it's done.

     PS:

        * Right after you finish updating driver, you must close and
          re-open and adapter's propertis to validate the properties.

        * If you had updated the driver once before, the wizard will not
          find the driver in your diskette/CD-ROM drive. Instead of it,
          there should be one located in

                c:\winnt\inf\oem0.inf   (or oem1, oem2...)

          It is the same one as the diskette/CD-ROM, choose it and continue
          the rest of the steps.

 Driver keywords
 ---------------
     - Open 'Device Manager' in "My Computer" -> "Control Pannel" -> "System".
       Double click "D-Link DFE-550TX ...", Select "Advanced" item.

       Connection Type      Specify the connection type for the adapter.
                            Default: AutoSense

       Network Address      You can set the Ethernet address for your
                            adapter. It is not recommended to use this
                            keyword. As you know two or more adapter in
                            the same network with same Ethernet address
                            will cause a little problem.

                            When using this keyword you need to input
                            exactly 6 bytes of Ethernet address using
                            one of the following format:

                              xx-xx-xx-xx-xx-xx
                            OR
                              xxxxxxxxxxxx

                            Default: read address from adapter ROM.

       802.1Q/1P VLAN       You can enable it for VLAN group.
       tagging              Default: disable

       VLAN ID              This value will active after 802.1Q/1P VLAN
                            tagging enable.

       GVRP                 Support GVRP and will active after 802.1Q/1P
                            VLAN tagging enable.
                            Default: disable